![]() If your model doesn't have this button, you likely have to use the "On/Off" button. If your model has arrow buttons, use them to cycle through the various options and select them with the "Set" button.Use the "Hour" and "Min" button to select the specific timing for the event, taking care to note AM and PM hours.The other possibilities are combinations such as "SaSu" and "ThuFriSa." For example, "MoTuWeThFrSaSu" is every day of the week, while "Mo," "Tu," "We," "Th," "Fr," "Sa," and "Su" each represent individual days. Press the "Week" button to cycle through each day or combination of days of the week.For each event, set the week (day of the event), hour, and minute, followed by the start time-which is "# ON"-for the appliance as well as the stop time, which is "# OFF." The default "Program" display is "1 ON." As you press the "Program" button, the display cycles through each event: "1 ON," "1 OFF, "2 ON, "2 OFF," all the way until the maximum number of events. Each product has different capabilities, but can typically set up to 8 or so events. Note that the screen blanks if the battery is discharged completely.ġ5086 Manual Version 2 11-24-2009 your timer for different events using the "Program/Prog" button. This timer is equipped with a rechargeable Ni-Mh battery which will protect your programs during power failure for up to 30 days. For example if the current time is 2:00PM and you just programmed the unit to turn ON at 1:00PM, you will need to press the manual override key to turn it ON.Thereafter, the unit will resume normal operation (automatic). When you initially program the unit it may be necessary to press the manual override key as the unit will not look back to determine if it should be ON. Pressing the door will override the timer setting and will manually turn the switch ON and OFF. Then press the “PROG” key in order to delete this particular program.ġ20VAC 60Hz 15A Resistive 15ATungsten 1HP Then press the “HOUR” and “MIN” keys until -:- is displayed. ![]() To delete a particular program simply press the “PROG” key until the desired program is displayed.Ģ. When complete press the “CLOCK” key to return to current time and day.ġ. Any program can be edited by pressing the “HOUR”,“MIN”, and “DAY” keys.Then press the “PROG” key in order to accept the changes.ģ. Each time you do this you will be able to scroll thru the programs.Ģ. To review the programs that have been entered, press and release the “PROG” key. Follow the steps above to complete programming.ġ. When programming ON/OFF events, all days are indicated by default.To change the day selection simply keep pressing the Day key and the display will change as follows:Ħ. Note that a total of 7-ON and 7-OFF events can be programmed.ġ. If complete press the “CLOCK” key to return to current time and day.ĥ. When complete press the “PROG” key once.Ĥ. See block programming below for selecting different days. Using the “HOUR” and “MIN” keys enter the desired OFF time. When complete press the “PROG” key once.ģ. Using the “HOUR” and “MIN” keys enter the desired ON time. Press the “PROG” key once.TIMER 1 on - : - appears.Ģ. Now the timer is in operation and ready to be programmed.The colon “:” after the hours will continuously flash indicating that the clock is running.ġ. Release the “CLOCK” key once the time and day have been entered. If any keys are pressed for a prolonged period, the display will advance rapidly.Ħ. Press the “DAY” key to advance the day.ĥ. Press the “MIN” key to advance the minutes.Ĥ. Press the “HOUR” key to advance the hours.ģ. Press and HOLD the “CLOCK” key during this entire procedure.Ģ. The display should flash 12:00AM on Monday.ġ. Press the “RESET” button using a paper clip.Ĥ. Lift up the bottom of the door using a small slotted screwdriver.ģ. ![]() Mount the timer to the wall box being careful not to crush any wires.ġ. Once char ged, pres s the reset ( r ) button in the lo wer left corner using a t oothpick or pencil. Setup If numbers are di cult t o read or not visible on screen, plu g ti me r into an outlet and let timer char ge for 1 hour. Tuck the wires into the wall box leaving room for theTimer. Download myTouchSmart 36253 Operation & user’s manual 1 2 1. Note: Be sure that all wire nuts are secure.Ĥ. Often neutral wires can be found in the back of the wiring box wrapped in a wire nut.Ĭ) Connect the Hot/Live wire of Load to the Red wire fromTimer.ĭ) Connect the Ground wire to the Green wire fromTimer. Connect the wires ofTimer and wall box as followed by using the wire nuts provided.Ī) Connect the Hot/Live wire of main power to the Black wire fromTimer.ī) Connect the Neutral wires in outlet box to the White wire fromTimer.
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |